SIMCOMs SIM 900A in Europe? Read on and I'll show you how. SIMCOM SIM 900A module. The SIMCOM SIM 900A module is made for the Asian market, and will not get registered on a European network. To make it work, you'll need to do a firmware upgrade.
Use your preferred search engine to find the firmware file. Madhubala tamil serial episode 1. In this article, I'm using ”1137B03SIM90064STENHANCE.cla” To do the actual upgrade, you'll need a program called “Simcom – sim900 Customer flash loader”.
I have version 1.01. This program transfers the firmware from your computer to the SIMCOM module. For hardware, I'm using a SIMCOM SIM900A module, a SIM card, a serial cable, a computer running windows, and a breadboard. Connect the components in accordance with this picture. Connected to the breadboard. On this module, there are two different ways to connect it to other circuits.
One way is to use (TTL) and the other is to use the onboard MAX232 IC. I'm using the second option.
To enable the MAX232 IC, you need to install some jumpers on the 2x3 pin header. Jumpers are installed. To check that you've connected everything correctly, open up hyperTerm or some other serial communication program. In this article, I'm using GtkTerm. This is a Linux program, but that's OK; this is only to check connections.
To do the actual upgrade, I need to move over to my Windows computer. Got connected? When the serial program is opened, you can use any standard baud setting. When the SIM900A starts up, it goes into an auto-baud detection state. I've used 2400, 4800, 9600, and 115 000 successfully.
Now that the serial program is running, and everything is connected to your computer, you'll see something like this when you power up the module: Initial signs of a successful connection. To check the connections and verify that we're talking to the SIM900A module, type AT and hit enter.
If everything is working, you'll get an OK in return. Communications are working. AT-commands To communicate with the SIM 900A, we're using something called AT-commands; it's short for ATtension. After the AT, we need an instruction. To see if the module is connected to the network, we can use the 'AT+CREG?' Or to see which operator you're connected to, you can execute 'AT+COPS?'
There are a ton of different AT commands you can use, read more about them. Testing different AT commands. This image is from after the firmware have been upgraded. The 'AT+CREG?'
Command shows Network Registration The 'ATCOPS?' Command shows the Operator Selection There's also an online module tester.
At, you'll find a java-based module that connects to your module so you can test various AT-commands. You can use the picture above for connection reference. Upgrade the firmware. Now that we're connected to the module with the command 'AT+COPS?' , you get no service provider name, and now it's time for an upgrade. Start by downloading and installing the program “Simcom – sim900 Customer flash loader”.
P susheela kannada mp3 songs free download. Best Of P Susheela Kannada Music Playlist on Gaana.com. Download and listen to Best Of P Susheela Kannada on Gaana.com. Hits Of P Susheela (kannada Film Compilation) Songs Download- Listen Kannada Hits Of P Susheela (kannada Film Compilation) MP3 songs online free.
Flash Update Tool
Follow these simple steps:. Download and install “”. Yips drivers of globalisation tesco. Download the firmware you need. In this article, I'm using ”1137B03SIM900M64STENHANCE.cla”. Open up the sim900 Customer flash loader, and load the firmware file.
Click start. The program will start to erase the flash and then upload the new flash. The erasing part might take a few minutes, and it looks like nothing is happening. After a while, text will run in the infobox, and the progress bar will begin to show progress. If you get “Download done” at the end, you've successfully flashed a new firmware to your SIM900A module. Flash file loaded. Erasing current firmware.
Writing new firmware. Download done - message. To check that everything is working, and you have a service provider, close the Customer flash loader and start a terminal program again.
You'll need to turn the power off and on to let the module go into operation mode, with the auto-baud setting active. If you write the command AT+CPOL?, you'll see the name of your service provider. Now you have a SIM900A module, with new firmware, ready for action.
Next Article in Series: Give this project a try for yourself! I have a SIM900 shield for Arduino-UNO and a simple standalone SIM900A board.
Also I have a SIM pre-paid card from the SIMYO provider (Dutch) The card works in my cell phone. I reflashed both SIM900 modules with the file as mntionned above. The scan command shows all the networks around my home. But both the SIM900’s won’t connect to the network. After I enter the PIN code the SIM900 goes powerdown after 15 seconds. The SIM900A keeps poweron but the red LED keeps flashing every second. What can be be wrong?
Hi I have the version 1008B11SIM300C32SST34HF3284 of simcom I obtain the 1008B13SIM300C32SST34HF3284 firmware but I have problem with the Domain service, I can't use this function the B13 have problem with domain GPRS connection, they only connect by IP, you available the B14 version?? This version fix the problem domain,can you help me, but if you need the B13 version I can send to you.
Thanks Harold quote='sheikhfayaz'hello every body i have a simcom sim300 module when i upload the total flash it uploads successfully but when i download the total flash to module it displays message AREA OUT OF BOUND please help whats problem. The file version is: 10.0.8(XMST)3010SST34HFP2(216) PLEASE HELP THANKS IN ADVANCE/quote. Hi I have the version 1008B11SIM300C32SST34HF3284 of simcom I obtain the 1008B13SIM300C32SST34HF3284 firmware but I have problem with the Domain service, I can't use this function the B13 have problem with domain GPRS connection, they only connect by IP, you available the B14 version?? This version fix the problem domain,can you help me, but if you need the B13 version I can send to you.
Thanks Harold quote='sheikhfayaz'hello every body i have a simcom sim300 module when i upload the total flash it uploads successfully but when i download the total flash to module it displays message AREA OUT OF BOUND please help whats problem. The file version is: 10.0.8(XMST)3010SST34HFP2(216) PLEASE HELP THANKS IN ADVANCE /quote.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |